Skip to Main Content

Plumbing

Hand Tools - CC Line F

Intro to Hand Tools
Project CC-F #4
Tape Measures
Project CC-F#5
Intro to Chisels
Project CC-F#6
Mortise Cuts
Project CC-F#6
Chopping Out
Project CC-F#6
Pairing Cut
Project CC-F#6
Chop and Pare a Groove
Project CC-F#6
Sharpening a Cold Chisel and Center Punch
Project CC-F#6
How to use a Hacksaw
Project CC-F#7
Hacksaw Project
Project CC-F#7
Cutting with a Cold Chisel
Project CC-F#9
Chalk Lines
Combination Squares
How to use Files
Introduction to Handsaws
How to use a Crosscut Saw

Solder & Welding - CC Line JJ

How to solder copper pipe like a pro. Part 1 of 2
Project OC-H#40
How to solder copper pipe like a pro. Part 2 of 2
Project OC-H#40

Fixtures - SP Line H

Quick and Easy Bathtub Installation
Project SP-F # 58 & 59
How To Install A Kitchen Sink
Project SP-F #58 & 59
How To Install A Kitchen Sink Drain
Project SP-F #58 & 59
How To Install A Kitchen Faucet
Project SP-F #58 & 59
How To Install a Toilet
Project SP-F #58 & 59
How to Install a Drop-In Bathroom Sink
Project SP-F #58 & 59
How to Install A Fiberglass Shower
How to Install A Shower Water Valve

Power Tools - CC Line G

Drill Press
Project CC-F#4
PO Tool Layout
Project CC-G#8
Shower Drain Wrench Layout
Project CC-G#10
Reciprocating Saw
Project OC-F#31
Milwaukee Angle Drill
Project OC-F#31
DeWalt Angle Drill
Project OC-F#31
Angle Drill (water lines)
Project OC-F#31
Angle Drill (overhead holes)
Project OC-F#31
Steel Stud Hole Saw and Punch
Project OCC-F#32
Steel Stud and 2x6 Backing
Project OCC-F#32

Fasteners - CC Line L

SP Line D

Lifting Loads - CC Line H

Knots and Hitches
Project CC-H#16
How to Whip the End of a Rope
Project CC-H#16
Pipe Rigging
Project CC-H#17
Horizontal lift with Manila Rope
Vertical Lift with Manila Rope
Vertical Lift

Hand Tools II - OC Line E

Tubing Cutters
Project CC-L#21
Small Diameter Tube Bending
Project CC-L#21
Flared and Compression Fittings
Project CC-L#21
Flared and Compression Fitting Project
Project CC-L#21

Piping Equipment - OC Line G

RIDGID - How to Cut, Ream and Thread Pipe By Hand
Project OC-G#37
Ridgid Instructional Overview - 819 Nipple Chuck
Project OC-G#37
Power Vise (cutting and reaming)
Project OC-G#37
Drop Head Die
Project OC-G#37
Rigid 300
Project OC-G#37
How to use a pipe threader threading a steel pipe
Project OC-G#37
How Roll a Groove in a Pipe using RIDGID 916 and 300 tools
Project OC-G#37
Threading ½” -2” Pipe Using the Hand-Held Power Drive and Support Arm
Project OC-G#38
RIDGID 300 Power Drive Instructional Video
Project OC-G#38
Using a Geared Threader for 2-1/2” – 4” pipe
Project OC-G#39
Ridgid 535 pipe threader in operation
RIDGID 690- Power Threader Pipe capacity ½" - 2"

Last Updated: Jun 20, 2025 10:17 AM
URL: https://libguides.kpu.ca/plumbing
Print Page

Subjects: Trades and Technology

Tags: plumbing, trades